Farrow and Ball Dead Flat

Farrow & Ball Dead Flat is a multi-surface, ultra-matt finish with added toughness. Suitable for walls, woodwork and metal, it's ideal for colour drenching. The flat matt look creates richer colour from every angle, while the washable, scuff-resistant finish is more than a match for mess, perfect for hallways, playrooms and other high-traffic areas.

Farrow & Ball Dead Flat can be applied to various substrates, please refer to the product data sheet for a comprehensive guide to preparation.

Always make a test area before the application to judge the suitability of the product. Follow the manufacturer's instructions at all times. Ensure all surfaces are sound, clean, dry and free from dirt, grease and other contamination

Please note: Darker/stronger colours may require additional coats. The drying and recoat times provided are based on applying paint in normal conditions. Drying times may be longer in cooler and/or higher humidity environments. Darker colours may take longer to dry. Allow a minimum of 14 days before applying over solvent based coatings. Allow the full recoat time of 4 hours between coats as due to the matt appearance it looks dry a lot faster than it is, leaving the full recoat time is important as the chemical processes that enable durability in the paint happen in this time.

Applying Paint to Wall by Brush

1. Stir thoroughly before use
2. For best results use a quality fine-tipped synthetic bristled paint brush
3. Brushing first in a vertical direction then in a horizontal direction until an even coating has been applied
4. Allow to dry completely for a minimum of 4 hours before applying a second coat
5. On application of the final coat lay off the paint in a single direction to ensure that any brush marks and brush patterning effects (sometimes visible in certain lighting conditions) are minimised

Applying Paint to Trim by Brush

1. Stir thoroughly before use
2. For best results use a quality fine-tipped synthetic bristled paint brush
3. Load the brush well and apply a generous first coat
4. Brushing first in a vertical direction then in a horizontal direction until an even coating has been applied
5. Finish off by 'laying off' the paint in one direction using light pressure, with the brush held at an angle of approximately 30°
6. Allow to dry completely for a minimum of 4 hours before applying a second coat
7. When painting doors or cabinetry, it's important to lay off (paint your final strokes) in the direction of the grain, finishing the brush stroke at the visible carpentry joints for a flawless finish

Applying Paint to Walls by Roller

1. Stir thoroughly before use
2. Use a medium pile woven polyester roller
3. Apply the paint in diagonal strokes to create wither an 'M'. 'W' or 'V' shape
4. Fill in and over the shape you have just painted to spread the paint evenly
5. Repeat this process, working in small sections, always work from wet to dry areas, maintaining a wet edge to minimise roller marks
6. Allow 4 hours between coats
7. On application of the final coat lay off the paint in a single direction to ensure that any roller patterning effects (sometimes visible in certain lighting conditions) are minimised.

Applying Paint to Trim by Roller

1. Stir thoroughly before use
2. Paint can be applied using a medium pile woven polyester roller, this will provide a good finish with minimal stippling and is a quick method of application
3. Where an optimum finish is required, it is recommended brush application using a fine-tipped synthetic bristled brush

Farrow and Ball Dead Matt is washable & wipeable. As is standard for all decorative paints, we recommend that you leave a period of 2 weeks for the paint to fully harden or cure. During this time it's a good idea to treat the area with care and avoiding harsh cleaning.

Wipe gently with a soft damp microfibre cloth or sponge. Some cleaning solutions may mark the surface. Test on an inconspicuous area before use. Do not use bleach-based cleaning products. Surface scuffs and marks may be more visible on some darker colours; these can be easily wiped away with a damp microfibre cloth. Staining can be minimised by not allowing time for the stain to penetrate the surface.